Aquanaut 20RX

[three_fourth]

Aquanaut 20RX

“…The planning hull, with a double keel feature, gave it directional stability, while climbing and descending the successive swells. The unsinkable hull, coupled with the novel self baling decks, gave such a measure of confidence, that I consider it the best design feature of the boat…”

Excerpts from the testimonial by FRANCIS C H LEE, the President of Raffles Marina.  Read full testimonial.

 
STANDARD SPECIFICATION

Fully moulded in glass reinforced polyester (GRP) or (FRP) incorporating a double-skin foam filled construction using HLU-open moulding technique.

HULL
Modified V-hull with integrally moulded spray rails to determine high efficiency, minimum spray and back wash is specially designed by Dynaglass. This special design incorporates a twin keel forming an air pocket below the hull. Thus when going over choppy waters, the surface effect lifts the boat up enabling a soft ride and extremely good directional stability. Apart from giving the craft enhanced qualities and ride, this also improves both speed and fuel efficiency.

GRP lay-up incorporates woven roving, chopped strand mat, cloth and high-density core.

Longitudinal and transverse stiffening combined with structural bulkhead giving immense strength. Completely foam-filled bulkhead compartments for excellent buoyancy making it virtually unsinkable.

DECK
Deck has integral non-slip surface moulded in and is designed with a highly efficient self-bailing system. Specially designed by Dynaglass with the scuba diver/diver in mind, the free board at the aft end is cut-off reducing the height of free board to the minimum. Thus enabling and facilitating easy access for divers.
Other attractive features includes clean, large, clutter-free working areas both forward and aft of the boat. Deck lay-up incorporates marine ply parquet, reinforcing core stiffenings for high strength and rigidity.

1.0 FORWARD AREA
1.1 Anchor/rope well c/w hinged cover
1.2 Life buoy compartment.
1.3 Forward step c/w side seats
1.4 Stainless steel 22 mm bow rail (optional)

2.0 MIDSHIP AREA
2.1 Two pairs of scuba tank pockets.
2.2 Two storage areas c/w stainless steel hinged cover on starboard side compartment.
2.3 Steering console box w/o wheel, system, control cables etc. (bare).
2.4 One fold-on helm seat c/w GRP suspension.
2.5 One pair 22 mm dia stainless steel handrails (optional)
2.6 One stainless steel radar arch c/w collapsible canopy frame bimini top and two rod
holders (optional).
2.7 Additional rod holders to be fitted on radar arch (optional).
2.8 Navigation and anchor lights (optional).

3.0 AFT AREA
3.1 Fuel tank storage compartment c/w hinged cover carries up to four standard 23-litre
fuel tanks.
3.2 Battery storage compartment.
3.3 Two wooden racks in each compartment.
3.4 Anodized aluminum transome trim.
3.5 Stainless steel transome plate complete with marine ply engine pad.
3.6 One pair marine ply fenders at aft.

4.0 DECK FITMENTS
4.1 Four heavy-duty PE drains plugs.
4.2 HDPE fender.
4.3 Five nylon cleats.
4.4 One stainless steel tow eye.
4.5 One stainless steel transome U-bolt.
4.6 Two PE drain plugs.
4.7 One pre-installed electrical wiring along starboard side gunwhale.

This specification is meant to fairly represent what is intended in the 20RX. However we reserve the rights to modify, add or delete to this in the best interest of producing the 20RX to the highest quality.

[/three_fourth]

[one_fourth_last]
Starlet
Fisherman 18DX
Fisherman 20DX
Aquanaut 20RX
Albacore
[/one_fourth_last]